 |
| [Us] rated supply voltage | 380...480 V (- 15...10 %) |
| Accellerations- og nedreguleringsrampe | Automatic adaptation of ramp if braking capacity exceeded, by using resistor Linear adjustable separately from 0.01 to 9000 s S, U or customized |
| Accuracy | AO1 +/- 1 % for a temperature variation 60 °C AI2 +/- 0.6 % for a temperature variation 60 °C AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C |
| Ambient air temperature for operation | -10...50 °C without derating |
| Ambient air temperature for storage | -25...70 °C |
| Analoge Indgange | 2 |
| Analoge udgange | 1 |
| Antal adresser | 1...247 til Modbus 1...127 til CANopen |
| Antal digitale udgange | 2 |
| Anvendes til | Asynchronous motors Synchronous motors |
| Bredde | 240 mm |
| Analog indgangstype | AI2 software-configurable voltage 0...10 V DC, input spænding 24 V max, impedans 30000 Ohm, opløsning 11 bits AI2 software-configurable current 0...20 mA, impedans 242 Ohm, opløsning 11 bits AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input spændi |
| Analog udgangstype | AO1 software-configurable voltage 0...10 V DC, impedans 470 Ohm, opløsning 10 bits AO1 software-configurable current 0...20 mA, impedans 500 Ohm, opløsning 10 bits AO1 software-configurable logic output 10 V <= 20 mA |
| Asynkron motorkontrol | ENA (Energy adaptation) system for unbalanced loads Flux vector control (FVC) with sensor (current vector) Sensorless flux vector control (SFVC) (voltage or current vector) Voltage/frequency ratio (2 or 5 points) |
| Beskyttelsestype | Motor thermal protection Motor power removal Motor motor fase brud Køre thermal protection Køre short-circuit between motor phases Køre overvoltages on the DC bus Køre over varme beskyttelse Køre overcurrent between output phases and earth Køre line suppl |
| Bremsemoment | 30 % without braking resistor < 150 % with braking or hoist resistor |
| Bremsning ved stilstand | Med DC indsprøjtning |
| Dataformat | 8 bits, odd even or no configurable parity til Modbus på terminal 8 bits, 1 stop, even parity til Modbus on front face |
| Dielektrisk gennemslagsholdbarhed | 5092 V DC between control and power terminals 3535 V DC between earth and power terminals |
| Digital indgangslogik | LI6 (if configured as logic input) positive logic (source), < 5 V (tilstand 0), > 11 V (tilstand 0) LI6 (if configured as logic input) negative logic (sink), > 16 V (tilstand 0), < 10 V (tilstand 0) LI1...LI5 positive logic (source), < 5 V (tilstand 0), > |
| Digital indgangsnummer | 7 |
| Digital indgangstype | PWR : safety input 24 V DC, impedans: 1500 Ohm i henhold til ISO 13849-1 level d LI6 : switch-configurable PTC probe 0...6, impedans: 1500 Ohm LI6 : kontakt-konfiguration 24 V DC med level 1 PLC, impedans: 3500 Ohm LI1...LI5 : programmering 24 V DC med le |
| Digital udgangstype | R2A, R2B configurable relay logic No, elektrisk varighed 100000 kredsløb R1A, R1B, R1C configurable relay logic NO/NC, elektrisk varighed 100000 kredsløb |
| Driftshøjde | 1000...3000 m with current derating 1 % per 100 m <= 1000 m without derating |
| Driftsstilling | Vertical +/- 10 degree |
| Dybde | 266 mm |
| EAN-nummer | 3389118069510 |
| Electromagnetisk kompatibilitet | Voltage dips and interruptions immunity test i henhold til IEC 61000-4-11 Radiated radio-frequency electromagnetic field immunity test i henhold til IEC 61000-4-3 Level 3 Electrostatic discharge immunity test i henhold til IEC 61000-4-2 Level 3 Electrical |
| Elektrisk tilslutning | L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 50 mm2 / AWG 1/0 AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm2 / AWG 14 |
| EMC filter | Integrated |
| Faseantal | 3 faser |
| Forsyning | Internal supply, 24 V DC, spændingsgrænser 21...27 V, <= 200 mA til overload and short-circuit protection Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %, <= 10 mA til overload and short-circuit protection |
| Forsyningsspændingsgrænser | 323...528 V |
| Forureningsgrad | 3 i henhold til UL 840 2 i henhold til EN/IEC 61800-5-1 |
| Frekens | 4...16 kHz with derating factor 1...16 kHz Justerbar |
| Functionality | Full |
| Fysisk interface | 2-wire RS 485 til Modbus |
| Hyppig beslutning | Display enhed 0.1 Hz Analog indgang 0.024/50 Hz |
| Hastighedsområde | 1...50 til synkron motor in open-loop mode, without speed feedback 1...1000 til asynchronous motor in closed-loop mode with encoder feedback 1...100 til asynchronous motor in open-loop mode, without speed feedback |
| Højde | 550 mm |
| IP kapslingsklasse | IP54 on lower part i henhold til EN/IEC 61800-5-1 IP54 on lower part i henhold til EN/IEC 60529 IP41 on upper part i henhold til EN/IEC 61800-5-1 IP41 on upper part i henhold til EN/IEC 60529 2-3 i henhold til EN/IEC 61800-5-1 2-3 i henhold til EN/IEC 605 |
| Isolation | Electrical between power and control |
| Isolationsmodstand | > 1 mOhmved 500 V DC for 1 minute to earth |
| Klemmetype | Male SUB-D 9 on RJ45 til CANopen 1 RJ45 til Modbus på terminal 1 RJ45 til Modbus on front face |
| Kommerciel status | Commercialised |
| Lagerkode | På lager |
| Ledningstype | Without mounting kit : 1-strand IEC cableved 45 °C, kobber 90 °C XLPE/EPR Without mounting kit : 1-strand IEC cableved 45 °C, kobber 70 °C PVC With an IP21 or an IP31 kit : 3-strand IEC cableved 40 °C, kobber 70 °C PVC With a NEMA Type1 kit : 3-strand UL |
| Linearitetsfejl | AO1 +/- 0.2 % AI1-/Al1+, AI2 +/- 0.15 % af maksimum værdi |
| Lokal indikering | 1 LED rød tilstedeværelse af drive voltage |
| Maximum sluttestrøm | R1, R2 til modstandsdygtig belastning, 5 Aved 30 V DC, cos phi = 1, R1, R2 til modstandsdygtig belastning, 5 Aved 250 V AC, cos phi = 1, R1, R2 til inductiv belastning, 2 Aved 30 V DC, cos phi = 0.4, R1, R2 til inductiv belastning, 2 Aved 250 V AC, cos ph |
| Maximum transient current | 99 A til 60 s 3 faser 30 kW / 40 hp 109 A til 2 s 3 faser 30 kW / 40 hp |
| Minimum sluttestrøm | Configurable relay logic 3 mAved 24 V DC |
| Motor slip compensation | Justerbar Automatic whatever the load Not available in voltage/frequency ratio (2 or 5 points) Suppressable |
| Motoreffekt i hp | 40 hpved 380...480 V 3 faser |
| Motoreffekt i kW | 30 kWved 380...480 V 3 faser |
| Mærkning | CE |
| Netfrekvensgrænse | 47.5...63 Hz |
| Nominal switching frequency | 4 kHz |
| Nominel udgangsstrøm | 66 A at 4 kHz 380 V 3 phases / 40 hp 52 A at 4 kHz 460 V 3 phases / 40 hp |
| Option card | Profibus DP V1 kommunikationskort Profibus DP kommunikationskort Overhead crane card Modbus/Uni-Telway kommunikationskort Modbus TCP kommunikationskort Modbus Plus kommunikationskort Interface card for encoder Interbus-S kommunikationskort I/O extension c |
| Polaritetstype | Ingen impedance til Modbus |
| Product end of life instructions | Available Download Bortskaffelsesmanual |
| Product environmental profile | Tilgængelig Download Produktmiljøprofil |
| Productcertificeringer | CSA C-Tick GOST NOM 117 UL |
| Produktsortiment | Altivar 71 |
| Produktspecifik applikation | Complex, high-power machines |
| Produkttype | Frekvensomformer |
| Prospektiv kortslutningsstrøm Isc | <= 22 kA, 3 faser |
| Protokol for kommunikationsport | CANopen Modbus |
| REACh | Reference contains SVHC above the threshold - Go to CaP for more details |
| Regulation loop | Adjustable PI regulator |
| Relativ fugtighed | 5...95 % without dripping water i henhold til IEC 60068-2-3 5...95 % without condensation i henhold til IEC 60068-2-3 |
| RoHS (date code: YYWW) | Compliant - since 0946 - Schneider Electric declaration of conformity |
| Sammenbygningens type | With heat sink |
| Shockmodstand | 15 gn til 11 ms i henhold til EN/IEC 60068-2-27 |
| Prøvevarighed | LI6 (if configured as logic input) 2 ms, +/- 0.5 ms til separat input(s) LI1...LI5 2 ms, +/- 0.5 ms til separat input(s) Al2 2 ms, +/- 0.5 ms til analog input(s) AI1-/Al1+ 2 ms, +/- 0.5 ms til analog input(s) |
| Reaktionstid | R2A, R2B 7 ms, tolerance +/- 0.5 ms til separat output(s) R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms til separat output(s) AO1 2 ms, tolerance +/- 0.5 ms til analog output(s) <= 100 ms in STO (Safe Torque Off) |
| Specific application | Other applications |
| Speed accuracy | +/- 10 % of nominal slip til 0.2 Tn to Tn vridningsvariation without speed feedback +/- 0.01 % of nominal speed til 0.2 Tn to Tn vridningsvariation in closed-loop mode with encoder feedback |
| Speed drive output frequency | 0.1...599 Hz |
| Standarder | EN 55011 class A group 2 EN 61800-3 environments 1 category C3 EN 61800-3 miljø 2 kategori C3 EN/IEC 61800-3 EN/IEC 61800-5-1 IEC 60721-3-3 class 3C1 IEC 60721-3-3 class 3S2 UL Type 1 |
| Støjgrænse | 64 dB i henhold til 86/188/EEC |
| Sustainable offer status | Green Premium produkt |
| Synkronmotorkontrol | Vector control without speed feedback |
| Tilgangs metode | Slave til CANopen |
| Tilgangsstrøm | 66 A til 380 V 3 faser 30 kW / 40 hp 56 A til 480 V 3 faser 30 kW / 40 hp |
| Tilslutningsfrekvens | 50...60 Hz (- 5...5 %) |
| Tilspændingsmoment | L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 12 N.m AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m |
| Tilsyneladende effekt | 43.4 kVAved 380 V 3 faser 30 kW / 40 hp |
| Torque accuracy | +/- 5 % in closed-loop mode with encoder feedback +/- 15 % in open-loop mode, without speed feedback |
| Transmissionsstørrelse | 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps til CANopen 9600 bps, 19200 bps til Modbus on front face 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps til Modbus på terminal |
| Type nr. | ATV71 |
| Udgangsspænding | <= power supply voltage |
| Vibrationsmodstand | 1.5 mm peak to peak (f = 3...13 Hz) i henhold til EN/IEC 60068-2-6 1 gn (f = 13...200 Hz) i henhold til EN/IEC 60068-2-6 |
| Vægt | 37 kg |
| Transient overmoment | 220 % af motor vridningsmoment +/- 10 % til 2 s 170 % af motor vridningsmoment +/- 10 % til 60 s every 10 minutes |
| Transmissionsstel | RTU til Modbus |
