 |
| [Us] rated supply voltage | 200...240 V (- 15...10 %) |
| Accellerations- og nedreguleringsrampe | Automatic adaptation of ramp if braking capacity exceeded, by using resistor Linear adjustable separately from 0.01 to 9000 s S, U or customized |
| Accuracy | +/- 1 % (AO1)for a temperature variation 60 °C +/- 0.6 % (AI2)for a temperature variation 60 °C +/- 0.6 % (AI1-/Al1+)for a temperature variation 60 °C |
| Ambient air temperature for operation | -10...50 °C without derating |
| Ambient air temperature for storage | -25...70 °C |
| Analog indgangstype | Software-configurable voltage: (AI2)0...10 V DC - 24 V max - 30000 Ohm - resolution: 11 bits Software-configurable current: (AI2)0...20 mA - 242 Ohm - resolution: 11 bits Bipolar differential voltage: (AI1-/Al1+)+/- 10 V DC - 24 V max - resolution: 11 bit |
| Analog udgangstype | Software-configurable logic output: (AO1)10 V - <= 20 A Software-configurable current: (AO1)0...20 mA - 500 Ohm - resolution: 10 bits Software-configurable voltage: (AO1)0...10 V DC - 470 Ohm - resolution: 10 bits |
| Analoge Indgange | 2 |
| Analoge udgange | 1 |
| Antal adresser | 1...127 addresses for CANopen 1...247 addresses for Modbus |
| Antal digitale udgange | 2 |
| Anvendes til | Asynchronous motors Synchronous motors |
| Asynkron motorkontrol | Voltage/frequency ratio, 2 points Voltage/frequency ratio, 5 points Flux vector control without sensor, standard Voltage/frequency ratio - Energy Saving, quadratic U/f Flux vector control without sensor, ENA (energy Adaptation) system Flux vector control |
| Beskyttelsestype | Power removal for Motor Motor fase brud for Motor Thermal protection for Motor Imod løs fase for køre Line supply overvoltage for køre Line supply undervoltage for køre Imod overskridende maks. Hastighed for køre Break on the control circuit for køre Over |
| Bremsemoment | < 150 % with braking or hoist resistor 30 % without braking resistor |
| Dataformat | 8 bits, odd even or no configurable parity for Modbus på terminal 8 bits, 1 stop, even parity for Modbus on front face |
| Dielektrisk gennemslagsholdbarhed | 4230 V DC between control and power terminals 2830 V DC between earth and power terminals |
| Digital indgangslogik | Positive logic (PWR), < 2 V (state 0), > 17 V (state 1) Negative logic (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1) Positive logic (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1) Negative logic (LI1...LI5), > |
| Digital indgangsnummer | 7 |
| Digital udgangstype | Configurable relay logic: (R2A, R2B)NO - 100000 cycles Configurable relay logic: (R1A, R1B, R1C)NO/NC - 100000 cycles |
| Driftshøjde | 1000...3000 m with current derating 1 % per 100 m <= 1000 m without derating |
| Driftsstilling | Vertical +/- 10 degree |
| EMC filter | Integrated |
| Enhedens korte navn | ATV71 |
| Faseantal | 3 faser Enkel faset |
| Forsyningsspændingsgrænser | 170...264 V |
| Forureningsgrad | 2 conforming to EN/IEC 61800-5-1 |
| Frekens | 1...16 kHz Justerbar |
| Digital indgangstype | Safety input (PWR)24 V DC - 1500 Ohm Switch-configurable PTC probe (LI6) - 0...6 probes - 1500 Ohm Switch-configurable (LI6)24 V DC, with level 1 PLC - 3500 Ohm Programmable (LI1...LI5)24 V DC, with level 1 PLC - 3500 Ohm |
| Electromagnetisk kompatibilitet | Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 Conducted radio-frequency immunity test Level 3 conforming to IEC 61000-4-6 1.2/50 µs - 8/20 µs surge immunity test Level 3 conforming to IEC 61000-4-5 Electrical fast transient/bur |
| Elektrisk tilslutning | Terminal 6 mm² / AWG 8 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) Terminal 2.5 mm2 / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) |
| Forsyning | Internal supply: 24 V (21...27 V)DC - <= 200 A with overload and short-circuit protection Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 % - <= 10 A with overload and short-circuit protection |
| Fysisk interface | 2-wire RS 485 for Modbus |
| Hastighedsområde | 1...1000 asynchronous motor in closed-loop mode with encoder feedback 1...50 synchronous motor in open-loop mode, without speed feedback 1...100 asynchronous motor in open-loop mode, without speed feedback |
| Hyppig beslutning | 0.024/50 Hz for analog indgang 0.1 Hz for display enhed |
| IP kapslingsklasse | IP54 on lower part conforming to EN/IEC 60529 IP54 on lower part conforming to EN/IEC 61800-5-1 18-22 on upper part without blanking plate on cover conforming to EN/IEC 60529 18-22 on upper part without blanking plate on cover conforming to EN/IEC 61800-5 |
| Isolation | Electrical between power and control |
| Isolationsmodstand | > 1 mOhm at 500 V DC for 1 minute to earth |
| Klemmetype | Male SUB-D 9 on RJ45 for CANopen 1 RJ45 for Modbus på terminal 1 RJ45 for Modbus on front face |
| Ledningstype | UL 508 cable with a NEMA Type1 kit: 3 wire(s) - 40 °C, copper 75 °C / PVC IEC cable with an IP21 or an IP31 kit: 3 wire(s) - 40 °C, copper 70 °C / PVC IEC cable without mounting kit: 1 wire(s) - 45 °C, copper 70 °C / PVC IEC cable without mounting kit: 1 |
| Linearitetsfejl | +/- 0.2 % (AO1) +/- 0.15 % of maximum value (AI1-/Al1+, AI2) |
| Lokal indikering | 1 LED - rød - drive voltage |
| Maximum sluttestrøm | 2 A at 30 V DC on inductiv load - cos phi = 0.4 - L/R = 7 ms (R1, R2) 2 A at 250 V AC on inductiv load - cos phi = 0.4 - L/R = 7 ms (R1, R2) 5 A at 30 V DC on modstandsdygtig load - cos phi = 1 - L/R = 0 ms (R1, R2) 5 A at 250 V AC on modstandsdygtig load |
| Maximum transient current | 37.4 A for 2 s 3 phases / 5.5 kW / 7.5 hp |
| Minimum sluttestrøm | 3 mA at 24 V DC (configurable relay logic) |
| Motor slip compensation | Justerbar Automatic whatever the load Not available in voltage/frequency ratio (2 or 5 points) Suppressable |
| Motoreffekt i hp | 7.5 hp 3 phases 200...240 V 5 hp single phase 200...240 V |
| Motoreffekt i kW | 5.5 kW 3 phases 200...240 V 4 kW single phase 200...240 V |
| Mærkning | CE |
| Netfrekvens | 47.5...63 Hz |
| Nominal switching frequency | 8 kHz |
| Nominel udgangsstrøm | 27.5 A at 4 kHz, 230 V 3 phases / 5.5 kW / 7.5 hp 17.5 A at 4 kHz, 230 V single phase / 4 kW / 5 hp |
| Polaritetstype | No impedance for Modbus |
| Product specific application | Lift |
| Productcertificeringer | CSA C-Tick GOST NOM 117 UL |
| Produkttype | Frekvensomformer |
| Prospektiv kortslutningsstrøm Isc | <= 5 kA, enkel faset <= 22 kA, 3 faser |
| Protokol for kommunikationsport | CANopen Modbus |
| Option card | Overhead crane card Controller inside programmable card I/O extension card Interface card for encoder Kommunikation kort for CC-Link Kommunikation kort for Interbus-S Kommunikation kort for Profibus DP V1 Kommunikation kort for Profibus DP Kommunikation k |
| Prøvevarighed | 2 ms +/- 0.5 ms (Al2) - analog input(s) 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s) 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s) 2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s) |
| Range of product | Altivar Lift |
| Reaktionstid | <= 100 ms in STO (Safe Torque Off) 2 ms +/- 0.5 ms (AO1) - analog output(s) 7 ms +/- 0.5 ms (R2A, R2B) - discrete output(s) 7 ms +/- 0.5 ms (R1A, R1B, R1C) - discrete output(s) |
| Regulation loop | Adjustable PI regulator |
| Relativ fugtighed | 5...95 % without dripping water conforming to IEC 60068-2-3 5...95 % without condensation conforming to IEC 60068-2-3 |
| Sammenbygningens type | With heat sink |
| Shockmodstand | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
| Speed accuracy | +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation, without speed feedback +/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation, in closed-loop mode with encoder feedback |
| Speed drive output frequency | 0...1600 Hz |
| Standarder | EN 55011 class A group 2 EN 61800-3 environments 1 category C3 EN 61800-3 environments 2 category C3 EN/IEC 61800-3 EN/IEC 61800-5-1 IEC 60721-3-3 class 3C1 IEC 60721-3-3 class 3S2 UL Type 1 |
| Støjgrænse | 55.6 dB conforming to 86/188/EEC |
| Synkronmotorkontrol | Vector control without sensor, standard Vector control with sensor, standard |
| Tilgangs metode | Slave for CANopen |
| Tilgangsstrøm | 30.8 A for 240 V, 3 phases / 5.5 kW / 7.5 hp 29.9 A for 240 V, single phase / 4 kW / 5 hp 35 A for 200 V, 3 phases / 5.5 kW / 7.5 hp 34.9 A for 200 V, single phase / 4 kW / 5 hp |
| Tilslutningsfrekvens | 50...60 Hz (- 5...5 %) |
| Tilspændingsmoment | 3 N.m - 26.5 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) |
| Tilsyneladende effekt | 12.8 kVA for 240 V, 3 phases / 5.5 kW / 7.5 hp 7 kVA for 240 V, single phase / 4 kW / 5 hp |
| Torque accuracy | +/- 15 % in open-loop mode, without speed feedback +/- 5 % in closed-loop mode with encoder feedback |
| Transient overmoment | 220 %, +/- 10 % for 2 s 170 %, +/- 10 % for 60 s |
| Transmissionsstel | RTU for Modbus |
| Transmissionsstørrelse | 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus på terminal 9600 bps, 19200 bps for Modbus on front face |
| Udgangsspænding | <= power supply voltage |
| Variant | With integrated 7-segment display terminal |
| Vibrationsmodstand | 1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-6 |
